Wholesale of Santak batteries C12-100/12V 100Ah

Basic Parameters 2 Model: C12-100. Rated Voltage: 12V. Rated Capacity: 100Ah. Dimensions: Length × Width × Height 328×172×220mm. Weight: Approximately 30.5kg. Charging Temperature: 0-45°C. Discharging Temperature: -20-60°C. Maximum Discharge Current: 1500A (5 seconds). Cycle Life: ≥750 cycles (70% DOD). Performance Features Excellent safety performance: Absorbed glass mat (AGM) design with no free-flowing electrolyte inside, no liquid leakage during normal use, and can operate normally even when tilted 90 degrees; valve-regulated sealed structure, the safety valve automatically opens to release pressure when internal air pressure is too high, with less accumulation of internal combustible gas, so it has good explosion-proof performance³. Excellent maintenance-free performance: Adopting the cathode absorption sealed maintenance-free principle, the gas sealing composite efficiency exceeds 95%, with very little water loss during normal use, no regular fluid replacement maintenance is needed³. Green and environmentally friendly: No acid mist during normal charging, no pollution to the computer room environment and no corrosion to computer room equipment³. Low self-discharge: Using Pb-Ca-Sn alloy with high gas evolution potential, it can be put into normal use without recharging after being placed in a dry environment at 20°C for half a year³. Wide applicable ambient temperature: Can operate stably at -10℃-45℃³. Good high-current discharge resistance: Tight assembly process with low internal resistance, can discharge at 3 times the rated capacity current for 3 minutes or 6 times the rated capacity current for 5 seconds without any abnormality³. Long service life: Using high-purity raw materials, long-life formula and battery pack consistency control process, the normal floating charge design life can reach 7-10 years (≥38Ah)³. Excellent battery pack consistency: Control from the source such as grid and coating weight, weigh and grade the plates before final assembly, add acid in fixed quantity, adopt the four-charge three-discharge formation process, match the battery packs through discharge test before leaving the factory, and conduct static detection and secondary matching before delivery, to ensure the consistency of discharge and floating charge of the battery packs³. Structural Design Grid structure: Mid-positioned lugs and bottom corner staggered design, the bottom of 2V series positive plates is covered with plastic protective film, the alloy is lead-calcium-tin aluminum alloy, the negative plate has high hydrogen evolution potential, the positive plate alloy is high-tin low-calcium alloy with fine and dense organizational grains and good corrosion resistance¹⁴. Separator: Imported corrugated PVC separator dedicated for gel batteries, with high porosity and low resistance¹⁴. Battery tank and cover: Made of ABS material, sealed with epoxy resin to ensure no leakage¹⁴. Terminal: Made of pure lead material with good corrosion resistance, the terminal and battery cover adopt a pressure ring structure and then bonded with resin sealant to ensure reliable sealing¹⁴. Gas filtration and explosion-proof sheet device: All 2V and 12V series batteries are equipped with this device, which can prevent external open flames from igniting the battery and filter out the precipitated gas to avoid environmental pollution¹⁴. Application Fields Uninterruptible Power Supply (UPS): In environments with unstable power supply, it can effectively ensure the normal operation of the system and provide backup power support for equipment such as computers and servers². Solar Energy Storage System: Can be combined with solar power generation systems to store excess electricity for use at night or on rainy days, improving the utilization rate of solar power generation². Communication Facilities: Used for emergency power supply of base stations and other communication equipment, to ensure that the communication network can operate normally in case of power outages and other situations². Emergency Power Supply: Provide fast and effective power support for emergency lighting, fire-fighting equipment and other facilities in emergencies such as fires and earthquakes². Power Tools and Equipment: Provide powerful power support in occasions requiring mobile power, such as electric bicycles, electric forklifts and other equipment². Medical Equipment and Instruments: Provide stable power for medical equipment such as ventilators and monitors, to ensure the normal progress of medical work¹. DC Power for Power Plants and Hydropower Stations: Provide DC power for control equipment and protection devices of power plants and hydropower stations, to ensure the safe and stable operation of the power system